What regulations is OSHA cover under what act

Answers

Answer 1
Answer: The law requires employers to provide their employees with working conditions that are free of known dangers. The OSH Act created the Occupational Safety and Health Administration (OSHA), which sets and enforces protective workplace safety and health standards.

Related Questions

Determine the boundary work done by a gas during an expansion process if the pressure and volume values at various states are measured to be 300 kPa, 1 L; 290 kPa, 1.1 L; 270 kPa, 1.2 L; 250 kPa, 1.4 L; 220 kPa, 1.7 L; and 200 kPa, 2 L
What are the important factors needed to be considered while selecting a brake or clutch?
A furnace is shaped like a long equilateral triangular duct where the width of each side is 2 m. Heat is supplied from the base surface, whose emissivity is ε1 = 0.8, at a rate of 800 W/m2 while the side surfaces, whose emissivities are 0.5, are maintained at 500 K. Neglecting the end effects, determine the temperature of the base surface. Can you treat this geometry as a two-surface enclosure?
Given the latent heat of fusion (melting) and the latent heat of vaporisation for water are Δhs = 333.2 kJ/kg and Δhv = 2257 kJ/kg, respectively. Use these values to estimate the total energy required to melt 100 kg of ice at 0 °C and boil off 40 kg of water at 100 °C. a) 239,028 kJ b) 95,250 kJ c) 185,500 kJ d) 362,628 kJ e) 123,600 kJ
Which of the following was an effect of world war 2 on agricultural industry

A site is compacted in the field, and the dry unit weight of the compacted soil (in the field) is determined to be 18 kN/m3. Determine the relative compaction if the maximum dry unit weight was measured to be 17 kN/m3. Express your answer as a percentage (but do not write the percentage sign in the answer box).

Answers

Answer:

the relative compaction is 105.88 %

Explanation:

Given;

dry unit weight of field compaction, W_d_((field)) = 18 kN/m³

maximum dry unit weight measured, W_d_((max)) = 17 kN/m³

Relative compaction (RC) of the site is given as the ratio of dry unit weight of field compaction and maximum dry unit weight measured

Relative compaction (RC) = dry unit weight of field compaction / maximum dry unit weight measured

RC = (W_d_((field)))/(W_d_((max)))

substitute the given values;

RC = (18)/(17) = 1.0588

RC (%) = 105.88 %

Therefore, the relative compaction is 105.88 %

Which outcome most accurately portrays the future for the timber company in the following scenario?A timber company that cuts and sells its own wood has been in high demand for the past three years. The company has gone through many acres of forest in its area, but it is sure to plant tree seeds after it bulldozes a section.

The timber company will lose business soon because not many people will need to build houses and buildings anymore.
The timber company will run out of trees quickly because the seedlings will not have enough time to become full-grown timber.
The timber company will go out of business due to the rising number of buildings using cement and concrete rather than timber.
The timber company will continue to grow because of its good business practices, and it will become the number one timber company in the country.

Answers

Answer: The timber company will run out of trees quickly because the seedlings will not have enough time to become full-grown timber

Explanation: I got it right on Edge!!!! Hope this helps

(d) Arches NP is known for its spectacular arches that develop in the jointed areas of the park. Placemark Problem 2d flies you to Landscape Arch, the arch with the largest span in Arches NP. If the stresses that stretched the rock to form the joints were oriented perpendicular to the joint surfaces and the rock fins that contain the arches, what was the direction that the rocks were stretched? ☐ N-S
☐ E-W
☐ NW-SE
☐ NE-SW

Answers

Answer:

☐ NE-SW

Explanation:

Based on the description, the rock direction is North East - South West (NE-SW). Rocks generally can expand or compress depending on the type and magnitude of stress applied on the rocks. However, if the applied stress is sufficiently high, cracks and fractures will be created on the rock and it can ultimately lead to the formation of particles.

Internal and external flow boiling regimes?

Answers

Answer:

The flow boiling is also classified as either external and internal flow boiling depending on whether the fluid is forced to flow over a heated surface or inside a heated channel. The two-phase flow in a tube exhibits different flow boiling regimes, depending on the relative amounts of the liquid and the vapor phases.

. Were you able to observe ???? = 0 in the circuit you constructed during lab? Why or why not? Hint: What value of resistance would be needed for ???? = 0? 2. What feature in the time response of an RLC circuit distinguishes a critically damped response from an underdamped response? 3. Why must an op-amp be powered to be used in a circuit? 4. If you were handed a parts kit with an unknown op-amp, what information would you need to find prior to using it in a circuit?

Answers

Answer:

an attachment is below

Explanation:

1) the formula for damping coefficient id for RLC series circuit.

For \xi =0 you can make c=0 but inductor will still have some capacitance.

2) the responses of critically damped system and under damped system are shown with comments on their time response.

4) There can be many different answers to this question, but the 4 I have mentioned are the most important parameters we need to know about an unknown op-amp if we are to use it in our circuit.

Hope it answers all your questions.

At its current short-run level of production, a firm's average variable costs equal $20 per unit, and its average fixed costs equal $30 per unit. Its total costs at this production level equal $2,500. A. What is the firm's current output level? B. What are its total variable costs at this output level? C. What are its total fixed costs?

Answers

Answer and Explanation:

The computation is shown below

Total average cost + total variable cost = total cost

Let number of output be x

So,

Total fixed average cost = x × $30

Total variable cost = x × $15

Total cost = $2,500

Therefore,

$20 × x + $30 × x = $2,500

50 × x = $2,500

x = 50

Now the total variable cost is

= 50 × $20

= $1,000

And, the fixed cost is

= 50 × $30

= $1,500

Answer:

12 4

Explanation:

because the production average is variable